Ubiquiti Networks MFI-MSW Ficha Técnica

Wall Mount Motion SensorModel: mFi-MSW

8mFi™ Wall Mount Motion SensorJumper SettingsThe mFi-MSW has jumpers located inside the product casing. Typically there is no need to open the casing

9LEDIf you need to access the jumper settings, use a Phillips screwdriver to remove the screw at the base of the sensor. Lift the case up and the jump

10mFi™ Wall Mount Motion SensorDetection Pattern110°, 10 x 10 m at 25° CTop ViewSide View2.3 m2.5 m8 m10 m0.5 m

11SpecificationsSpecificationsmFi-MSWDimensions 146 x 66 x 52 mmWeight 127 gPower Supply 9 - 16VDC, 12VDC TypicalCurrent Drain 35mA @ 12VDCInfrared Se

12mFi™ Wall Mount Motion SensorGeneral WarrantyUBIQUITI NETWORKS, Inc (“UBIQUITI NETWORKS”) represents and warrants that the Products furnished hereun

13General WarrantyWarranty ConditionsThe foregoing warranty shall apply only if:(I) The Product has not been subjected to misuse, neglect or unusual

14mFi™ Wall Mount Motion SensorComplianceFCCChanges or modifications not expressly approved by the party responsible for compliance could void the use

15ComplianceThis device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: 1. this d

16mFi™ Wall Mount Motion SensorL’émetteur-récepteur décrit ici émet de l’énergie de fréquence radio. Bien que le niveau de puissance est faible, l’éne

17ComplianceRoHS/WEEE Compliance StatementEnglishEuropean Directive 2002/96/EC requires that the equipment bearing this symbol on the product and/or i

18mFi™ Wall Mount Motion SensorFrançaisLa directive européenne 2002/96/CE exige que l’équipement sur lequel est apposé ce symbole sur le produit et/ou

19Declaration of ConformityEnglish Hereby, UBIQUITI NETWORKS, declares that this UBIQUITI NETWORKS device, is in compliance with the essential require

20mFi™ Wall Mount Motion SensorLatviski [Latvian]Ar o UBIQUITI NETWORKS deklar , ka UBIQUITI NETWORKS device, atbilst Direkt vas 1999/5/EK b tiskaj m

Ubiquiti Networks SupportEmail: [email protected] (9 a.m. - 5 p.m. PST): 408-942-1153Online ResourcesWiki Page: wiki.ubnt.comSupport Forum: fo

1IntroductionIntroductionThank you for purchasing the Ubiquiti mFi™ Wall Mount Motion Sensor. This sensor is designed for use with the mFi mPort. Onc

2mFi™ Wall Mount Motion SensorHardware OverviewFrontMotion SensorBackmFi RJ45 Port

3Hardware InstallationHardware InstallationInstallation Tips• Avoid installing the sensor in areas where it will face direct or reflected sunlight.•

4mFi™ Wall Mount Motion SensorWall-Mount1. Use a 6 mm drill bit to drill two holes 20 mm apart with one directly above the other. 20 mm2. Insert the

5Hardware Installation4. Align the top hole of the Mounting Bracket over the screw and slide the Mounting Bracket down. 5. Use the Phillips screwd

6mFi™ Wall Mount Motion SensorConnecting the Cabling and Mounting Base1. Connect a straight-through CAT5/6 cable to the mFi RJ45 port on the mFi-MSW.

7Hardware Installation3. Connect the Mounting Base to the Mounting Bracket.4. Connect the other end of the CAT5/6 cable from the sensor to an mFi RJ